Sponsored

Convertible A-Pillar Trim Removal and Installation

UNSAFE

Well-Known Member
Joined
Jan 4, 2024
Threads
6
Messages
160
Reaction score
100
Location
Yorktown, VA
Vehicle(s)
'24 Mustang GT Vert, '25 RAM 1500 Limited Night Edition
Going to start installing a dash cam in the '24 Convertible and trying to figure out how to remove the passenger side A-pillar trim in order to run a wire to the dash cam mounted near the rear view mirror. I'm hard wiring it so can't use the USB port. Anyone know how to remove/reinstall this trim piece on a convertible? Thanks!
Sponsored

 

PS JCS

Active Member
Joined
Oct 15, 2024
Threads
2
Messages
30
Reaction score
22
Location
Palm Springs
Vehicle(s)
2024 Mustang GT convertible
I can't answer your question. But the Geek Squad did a great job installing my dash camera on GT convertible without removing anything. Get professional help
 

Neggytive

Well-Known Member
Joined
Mar 17, 2024
Threads
7
Messages
738
Reaction score
867
Location
Florida
Vehicle(s)
2024 GT Prem. convert. 401A 10 speed auto
normally they are just grab and tug to release the clips from the slots in the A pillar.

There is an airbag in back of the cover, you will probably find the cover has a tether on it to keep it from being shot across the car if the bag should deploy.
 

Fruitstang

Well-Known Member
Joined
Jan 7, 2018
Threads
11
Messages
306
Reaction score
204
Location
Germany
Vehicle(s)
2024 Mustang GT Convertible
Do not just pull, watch this Gen6 video first.
I presume Gen7 is very similar.

 
OP
OP
UNSAFE

UNSAFE

Well-Known Member
Joined
Jan 4, 2024
Threads
6
Messages
160
Reaction score
100
Location
Yorktown, VA
Vehicle(s)
'24 Mustang GT Vert, '25 RAM 1500 Limited Night Edition
Thank you all! Very helpful info!
 


jeffnudi

Well-Known Member
Joined
Oct 9, 2023
Threads
1
Messages
168
Reaction score
152
Location
Saint Marys, GA
Vehicle(s)
2024 Mustang EcoBoost Prem. Conv., 2022 Mav Hy XLT, 2015 Harley-Davidson FLHTK
Going to start installing a dash cam in the '24 Convertible and trying to figure out how to remove the passenger side A-pillar trim in order to run a wire to the dash cam mounted near the rear view mirror. I'm hard wiring it so can't use the USB port. Anyone know how to remove/reinstall this trim piece on a convertible? Thanks!
Just curious. Why not use the USB at the mirror?
 
OP
OP
UNSAFE

UNSAFE

Well-Known Member
Joined
Jan 4, 2024
Threads
6
Messages
160
Reaction score
100
Location
Yorktown, VA
Vehicle(s)
'24 Mustang GT Vert, '25 RAM 1500 Limited Night Edition
Just curious. Why not use the USB at the mirror?
I'm using parking mode with an add-on battery pack that requires 12 volts volts to recharge. It's. hardwired to the fuse box using an add-a fuse connector and uses a fuse location that is powered when the ignition is on (Accessory mode). The USB port is only 5 volts. Hope that helps.
 

jeffnudi

Well-Known Member
Joined
Oct 9, 2023
Threads
1
Messages
168
Reaction score
152
Location
Saint Marys, GA
Vehicle(s)
2024 Mustang EcoBoost Prem. Conv., 2022 Mav Hy XLT, 2015 Harley-Davidson FLHTK
I'm using parking mode with an add-on battery pack that requires 12 volts volts to recharge. It's. hardwired to the fuse box using an add-a fuse connector and uses a fuse location that is powered when the ignition is on (Accessory mode). The USB port is only 5 volts. Hope that helps.
Thanks. Useful information. I am just beginning to look into dash cams, so starting from zero.
 
OP
OP
UNSAFE

UNSAFE

Well-Known Member
Joined
Jan 4, 2024
Threads
6
Messages
160
Reaction score
100
Location
Yorktown, VA
Vehicle(s)
'24 Mustang GT Vert, '25 RAM 1500 Limited Night Edition
Thanks. Useful information. I am just beginning to look into dash cams, so starting from zero.
You're welcome! I'm a newbie also as I only started looking a couple of months ago myself. Good luck!
Sponsored

 
 








Top