Search results

There is a TSB for the quiet start issue when using remote start. Contact your ford dealer and ask them to make an appointment to do the update that fixes the quiet start issue, they should know what you are trying to do. The TSB Reference number is 24-2047.

ive seen someone else have a similar problem, itll be warrantied, no questions asked. fingers crossed on no rattles, my car goes in tomorrow for some obnoxious dash rattles, i wont take it back until they are fixed. This is the 3rd time ill have it in for rattles.

My performance pack GT didn’t come with these, had the car for 7 months now. Wish I had gotten them.

you realize that the transport mode is taken off by the dealer before you even have a chance to drive it? its a part of the delivery inspection. 19 miles is low especially if it had to be moved around storage lots or moved to a new area to be loaded on a train. the dealer also removes all...

is it by rail or not? rail always takes longer. Be optimistic, because chances are there wont be damage. you gotta think its being on and offloaded carts at different yards, it'll take a while. But even when it says shipped, does always mean its shipped. Mine eventually said shipped and also...

mine went "in production" on July 7th 23' and was stuck there until July 28th 23' when it went to "built", then no updates from then until it was an hour from my dealer on August 27th 23'. this is the new normal, dont expect it to update if it does, for another few days. Take a breath and chill.

check the top strut nuts, ive heard of cases where they don't tighten that top nut down fully and it causes clunks. I did my own progressives from steeda, and i used a caliper to measure the distance from the top of the nut to the edge of the stud and then after installing the springs, made sure...

Anyone know of any aftermarket ones available for the GT that arent the carbon fiber ones? would really like a set before my Tennessee weekend trip. Are they supposed to be front only or all 4 corners?

all EcoBoost's have the S/S and all mustangs have the sequential turn signals, they are referring to the hazards being on, Job 1 cars just flash the lights vs Job 2, the hazards are going sequential.

If you reach in and touch that white seal, that whole thing moves freely back and forth. That's why I thought it may be the issue, so if you don't have a noise then it's not the issue. I installed a hard wired dash cam and ran the wires along the headliner and down the A pillar, down to the BCM...

I see the same gap as mine so it's not the issue.

I'm trying to diagnose a rattle/buzz on the passenger side dash and can't figure it out. While doing it I had notice that the blower motor under the dash has a piece of tubing if you will that comes from the firewall and curves into the motor. Looking at it with the glove box out, the motor...

Anytime, I just took my Spoiler off to get painted this morning. If you plan on doing the Spoiler, beware the adhesive it TOUGH, and don't use fishing line as you may etch into the plastic panel. I did, nothing serious and will be covered by the Spoiler, but nonetheless lol.

I have a rattle very similar to what you described. Same situation when it occurs as well. I have narrowed it down to being in the doors, the rattle takes turns going from passenger side and drivers side, sometimes at the same time. Recently I've noticed it when I play music louder that has a...

I attached the instructions RTR provided me when I was looking to know how to remove the Spoiler, I didn't buy an RTR Spoiler, they were just helpful to proved these. You would remove all bolts, BESIDES the 2 under need the rubber grommets as it is labeled in the instructions.

Yes you can. The Spoiler js just attached with 2 10mm bolts and adhesive, to that plastic cover the reverse camera lives in. There are like 9 10mm bolts holding that housing to the decklid itself, in which you do not have to remove the 2 separate 10mm bolts from the Spoiler, to remove that cover...

Update, $100 and 15 minutes later, dents are gone and Spoiler is dropped off to be painted Gloss black. Can finally appreciate the look the black badges give to the atlas blue color!

There is a TSB for this issue from ford. If you call and make an appointment for the quiet start not working and ask them to do the update to fix it, they should know what you are talking about and get you in. Something in the software causes it to always start loud until you either hit the On...

extremely easy, just beware of the decklid denting possibility. Heat gun, pry tool/ fishing line and rubbing alcohol. took about 10 minutes total.

Ordered them from steeda. Ordered friday morning and got them monday afternoon. Says out of stock so it was a big Suprise for sure.