Search results

I did this in preparation for the K-member installation which would make oil changes more than a simple inconvenience. I also plan to track the car.

You are going to make a lot of people smile with that one.

I added a removable oil filter access panel to my GT. I plan to add a Steeda K-member to the cradle and I will not be going through an R&R to change the oil. I used a paint marker to trace the opening (while panel installed) by reaching through from the wheel well. I used a Dremel with 1/8...

No, the one under the engine. Looks like this: https://www.steeda.com/steeda-555-5536-mustang-extreme-g-trac-k-member-brace

It would look something like this: https://www.steeda.com/steeda-555-5536-mustang-extreme-g-trac-k-member-brace

Any chance you can take a pic?

I get that there is some terminology confusion. My complaint is that my performance pack car did not come with the brace below the engine. If it was supposed to have one from the factory then I need to take it back to the dealership to have them install one. That is why I was asking if they they...

Does a Ford Motorsport / OEM Under Vehicle K-Member exist? I have a 2025 GT with PP and the option list calls out a "black painted strut brace" and a "K brace" separately a few lines down. This made me think it came with a K member/brace. It does not have anything underneath. The thing that...

It came with 2-sided tape but I did not use it. I did not see a place that made sense to use it. They seem sturdy enough without.

Saw this on Facebook. They make decent points. Could be sponsored by Ford for all I know. I know I am tired of hearing the complaints that Mustang are not as cheap as they were before Biden. https://www.facebook.com/share/p/19igicqSdf/

Since the hood stripes were curved like a banana an I had a hard time aligning the last ones against the straight hoodline, I decided buy another set. At least they offer 1/2 off for oops purchase. I just couldn't handle seeing the crooked stripe from behind the wheel. I decided to cut the top...

I installed them last night. There were no instructions. They say so on ebay so that was not a suprise. They fit the body well and look as good as something like this can. They seem to be secured well. I do not plan to use scratch-o- matic so I will not be able to comment on that. I had to...

Total inflation is at least 25% since idiocy took over. Wages have not even come close to catching up with that. That's a big factor for poor sales. Most people are still in the hole.

Those are what I have.

I have watched many tests on these and the oem filters in general do not do a very good job of filtration. Motorcraft also has QC problems.

I just got this the Purolator Boss PBL22500 filter from Amazon and it has a couple problems. I am not crazy about how the core has a giant spiral seam and the perforations seem small. The check valve is also pinched at the crimp joint. I used a borescope camera to look inside. I will be doing...

I will measure and report back when I pull the wheels to install my splash guards. It will probably be this weekend.

I bought a set of non PP wheels for winter. there are gouges in the reliefs from studs bottoming and they never seated on the rotor face. They may have changed suppliers. The 30mm may be to the end of the last complete thread. I don't know. Just sharing to save someone else the hassle.

I got the tire wheel set because I didn't want to wait 4 months to drive my brand new car (summer only PP tires) I got them because of the all season tires. I am telling everyone that my 2025 wheel studs must be longer than the 2024 studs and not to assume 25mm spacers will fit without...

I just tried 25mm spacers on my 2025 GT with PP. I have a set of new take-off 19" gt silver wheels with All season tires. I could not use them as the studs were too long and dug into the back of the reliefs on the wheels. I did some measuring and it will take about 3mm of grinding to make the...